Groutings-Capgrout® HP

High Strength and Non-Shrinkable Grout (CapGrout HP)

CapGrout HP is a powder product containing cement, suitable aggregates, plasticizing admixtures, and expandable material to compensate for shrinkage that is used to fill the pores and joints up to 10 cm in thickness completely. This product has high strength in all ages as well as filling the joints and pores at the beginning of the setting (To compensate for shrinkage) due to the expanding property.

This product is produced based on the general requirements of the Iran National Standard No. 18644. Also, this grout meets the requirements of the ASTM C1107 standard.

Download technical file

The advantages of using the hardened and fresh grout:

The 28-day compressive strength: 80MPa
This product is a non-shrinkable or non-excessive expansion grout by developing the expansion equivalent to the probable shrinkage

The usage of the grout:

• It fills under the steel base plates
• Installing rebar and different systems of anchorage
• Filling the space between the foundation and the plates of placing the industrial machinery

The necessary notes for using the grout and grouting operation:

Each packet of this product fills 12 liters with the minimum amount of water.
It is necessary to clean the surfaces, joints, and holes from contaminations and dust before grouting. If these surfaces are loose and weak, they should be carved to reach the strong part.
The surface should be fully submerged at least 2 hours before grouting and discharged from water a little before grouting. Also, it is necessary to fully discharge bolt holes by an air pump.
The base plates and other steel materials should be clean from oil stains completely.
For grouting under plates, balancing the base plates is accomplished carefully by using suitable parts (Known as a shim) which are supplied by Capco Company.
The molding around the grout should be accomplished in a way that there will be no leakage. Using the sealing tapes and mastic are recommended for this purpose.
The suitable amount of water is calculated based on the volume of the desired grout and poured in a mixer with proper volume with an approximate speed of 400 rounds per minute. The suitable amount of water is approximately 2.7 liters per 25 kg of grout. The grout powder is gradually added to the mixture while mixing for up to 5 minutes.
The mixing should be done in the minimum time and in a way that obtains a homogenous and uniform mixture.
Mixing should be accomplished at 20˚C temperature and in a maximum time of 15 minutes to reach the efficiency of grout expansion to its maximum. This mixture is suitable for joints up to 10 cm and the washed dry clean aggregates with a maximum size of 10 mm can be used for bigger joints. In this situation the mixing ratio of sand and grout will be 1:1. This is done to reduce the cement hydration heat in high thicknesses. Besides, the properties of the grout depending on the amount of used sand can be different from the original product.
Continuous grouting is very important and therefore, the amount of the prepared grout should be proportionate to the volume of grouting. Grouting must be preferably done from one side so that no air is entrapped in the joint. The grout must be pumped for spaces with a high volume of grouting. Also, it is necessary to take the following tips into consideration:
Grouting must be done continuously
At temperatures above 25˚C, the considerations about concrete casting in hot weather must be considered.
Never use an excessive amount of allowable water to obtain higher consistency or to compensate for the decrease in consistency.

Physical and Chemical Specifications of the CapGrout HP:

Physical State: Powder
Color: Grey
The Specific Weight of the Powder: 1/7 ± 0/05 g/cm3
The Specific Weight of the ready mortar: 2/3 ± 0/02 g/cm3

Safety Precautions When Using the CapGrout HP:

• Blink in water for at least 15 minutes in case of eye contact
• Wash your skin with clean water for 15 minutes in case of any contact with the skin
• The contaminated clothes must be washed with suitable detergents to be usable for further work.
• It is necessary to visit a doctor if the injured individual still feels uncomfortable

Groutings-Capgrout® HP

— Our mission is to improve the quality of concrete —